 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DM100E Series UltraMiniature, 1W SIP Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: * 1W Output Power * UltraMiniature SIP Case * Low 0.3 Inch Profile * Single & Dual Outputs * 1,000 VDC Isolation * >3.5 MHour MTBF * 12 Standard Models * LOWEST COST!! Input Parameter Input Voltage Range Input Filter Reverse Polarity Input Current Conditions 5 VDC Input 12 VDC Input Min. 4.5 10.8 Typ. 5.0 12.0 Max. 5.5 13.2 0.3 Conditions Dual Output , Balanced Loads For Vin Change of 1% Min. Typ. 1.0 0.1 1.2 50 120 0.02 Momentary (1.0 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 60 100 Conditions Ambient Case Min. -40 -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +90 +125 Typ. Max. Units VDC M pF kHz Units C C C 0.03 75 Max. 3.0 1.0 Units VDC Internal Capacitor A Units % % % mV P - P % %/C Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit See Model Selection Guide RoHS Compliant General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Physical Case Size Case Material Weight 0.65 x 0.23 x 0.30 Inches (16.5 x 5.9 x 7.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Conditions MIL HDBK 217F, 25C, Gnd Benign Conditions 5 VDC Input 12 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 3.5 Min. -0.7 -0.7 Typ. Max. 9.0 18.0 300 450 Typ. Max. Units MHours Units VDC C mW Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number DM101E DM102E DM103E DM104E DM105E DM106E DM111E DM112E DM113E DM114E DM115E DM116E Input Voltage (VDC) Nominal 5 5 5 5 5 5 12 12 12 12 12 12 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 Full-Load 273 270 263 278 256 256 107 103 105 114 105 105 Current (mA) Load Regulation Voltage Current Current No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 30 30 30 30 30 30 15 15 15 15 15 15 5.0 12.0 15.0 5.0 12.0 15.0 5.0 12.0 15.0 5.0 12.0 15.0 200.0 83.0 67.0 100.0 42.0 33.0 200.0 83.0 67.0 100.0 42.0 33.0 20.0 9.0 7.0 10.0 5.0 4.0 20.0 9.0 7.0 10.0 5.0 4.0 15 15 15 15 15 15 15 15 15 15 15 15 Output Efficiency (%, Typ) 73 74 76 72 78 78 78 81 79 73 79 79 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 500 200 200 200 200 200 200 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capacitor values are given in Vin 5 VDC 12 VDC Input Capacitor 4.7 F 2.2 F Output Capacitor Single Dual 5 VDC 10.0 F 4.7 F 12 VDC 2.2 F 1.0 F 15 VDC 1.0 F 0.47 F Vout Derating Curve the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Pin Connections Pin 1 2 4 Single +Vin -Vin -Vout Dual +Vin -Vin -Vout Pin 5 6 Single No Pin +Vout Dual Common +Vout Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) * Pin 1 is marked by a "dot" or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com * 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 * FAX: (781) 344-8481 * E-Mail: sales@micropowerdirect.com |
Price & Availability of DM111E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |